"I gave it a slope outward" Why?
What's wrong with this picture? When I drove up to this property, I saw this problem right away.
The front porch was added after the fact by the new owners. They did'nt want the structure to touch the home. And when I asked "why is the front porch addition leaning outward"?
Their response was " I did'nt want it to touch the home. And I gave it a slope outward so the water would run off better".
I thought "you have to be kidding me". But i did'nt say anything.
Remember if your going to "improve" your home, then have a qualified contractor do the work.
There are simply way to many "uncle Bob's" out there who think they can do anything.
This was a poor design and a poorly installed "addition" to the home.
I think they detracted from the curb appeal the home originally had in the first place.
Stucco can be a nightmare.
Especially when not installed correctly. There are a lot of ways to install a stucco covering to a home or building of any size.
Just remember to use the proper materials to get the job done correctly.
This unit was a double unit that are rentals. This was only one of two buildings on site. The other building is a five unit complex.
This unit had siding issues. No maintenance for years is what it looked like to me.
This T-111 sideing was never maintained after installation 20 years ago.
Notice how "warped" the siding is? There were a lot of issues with he siding pulling loose from the framing of the structure.
In the next shot look at the way the stucco was installed at the parepet wall.
To me, it looks like the structure had never been maintained. I was surprised to "not see" more damages than I did.
Have a very good day everyone.
I thought, "oh good" they upgraded the electrical system. Or did they really.
As I inspect homes, not much surprises me any more. It seems that home owners are trimming so many corners they have nothing
left.
Note to "Uncle Bob" Cease and desist from any more home repairs.
My first impression of this home was good they upgraded the electrical system to handle the increased load to the home. I could'nt have been more wrong.
Here was the latest up grade to the home that was installed two years ago.
When I got in the home to check out all the sub panels I could only find one.
Note the "instructions to the breakers"? This would indicate to me there were a lot of issues with the breakers tripping. Notice any thing else about the contents of the breaker box?
There are only three breakers being used for the entire home. This is the "original breaker box that is still live" even though the electrical was "up graded".
To make matters even worse, in the attic there were issues like this little monster.
Yes this is live knob and tube in the attic. The amount of the home that was actually upgraded in the home was limited to the A/C supply line, the kitchen stove, The furnace and a couple of GFI plus and a couple of closet lights. That's it. All the rest of the electrical system stayed the same.
Live knob and tube.
Inspection went from good to bad to worse.
This recent inspection of a home was going well till I took a look at the "new roof". This roof was installed in 11 of 2011. This is the "GOOD" part.
I was thinking before I got on the roof that "being a new roof" there should be "no issues" for me to find.
I could'nt have been more wrong.
In this picture there are five things wrong. Can you pick them out?
This is the bad part.
1. The boot is the wrong size for the vent.
2. The vent has no cap.
3.The vent terminates below an eave. Not tall enough.
4. No step flashing used for the sidewall flashing.
5. The flashing that was used, was not properly fastened or sealed.
This is the worse part.
Yes, this is a live gas furnace vent. It was not secured in the attic where it connected to the furnace. It had slid down and was causing the vent to be out of alighnment and the exhaust to be running down hill.
The vent stack was too short to begin with. Another inspection with no mechanical inspector sign off anywhere to be found.
Have a great day everyone.
Furnace exhaust connections, the way not to do it right.
With all the ways to install furnaces, there is the right way the wrong way and then there is the contractors way.
It seems that if no one is watching the contractor, corners will be cut. Without a mechanical inspection for the new furnace. The installer will find every conceivable way to cut as many corners as possible.
Here are a few reasons to always get a permit and have the state or local "mechanical inspector" follow up behind the installer and make sure the installation was done correctly.
Can anyone tell me what this picture represents?
This furnace was installed in 2007, and has had "issues" from the day of installation.
There was a long list of "wrong" installation issues with this unit. There should have been a "approved sticker" on the unit with the permit number and the inspector contact information.
There was not anything on the unit about the installer or the permit and or inspection date.
Always have all mechanacle appliances pemited and inspected. If the locale mechanical inspector is doing their job. This would have never happened.
 |
|
|
We offer residential and commercial inspections. Residential and Commercial Green certification, and energy audits . Also insurance claim inspections and freight inspections. Desert Sun Inspections.
ActiveRain Corp. is not responsible for the accuracy of the site's content (which is written by members of the ActiveRain Real Estate Network) and does not endorse the views of the real estate agents, mortgage brokers, and others listed here.
Powered by the ActiveRain Real Estate Network
© 2013 ActiveRain Corp. All Rights Reserved
